Final assembly set comfort version - Peripheral supply and exhaust device PPB 30 K

Final assembly set comfort version - Peripheral supply and exhaust device PPB 30 K – Maico – 0095.0246 – 4012799952466: Final assembly set comfort version PPB 30 K, energy efficiency class=A, energy efficiency class spectrum=A+ to G, type of ventilation=decentralized supply and exhaust air, heat recovery via=other, heat source=outside air, nominal power=2.5 W, degree of heat provision=73% , With hot water preparation=no, With heating=no, With remote control=no, Air connection diameter=160 mm, Height=275 mm, Width=275 mm, Depth=410 mm, Weight=4.69 kg, Volume flow=26 m³/h, With water air heater=no, with additional heater=no, final assembly sets for the PushPull Balanced PPB 30 individual room ventilation unit with two fans, two ceramic heat exchangers, inner cover and two integrated filters (G3), so that the air is filtered in both directions. Versions: PPB 30 O object version, PPB 30 K comfort version with integrated humidity sensor and the possibility of volume flow compensation through PP 45 devices, PPB 30 RC radio version with integrated radio board including humidity sensor and the possibility of volume flow compensation through PP 45 devices. We recommend these devices in exhaust air rooms (toilet, bathroom, kitchen). This is possible without any problems thanks to the device protection class IP X4. Necessary accessories: shell sleeve PP 45 RHK or PP 45 RHL, external cover PPB 30 AK, PPB 30 AE, PPB 30 AW or PPB 30 AS, room air control RLS 45 K or RLS 45 O. With a room air control RLS 45 K or RLS 45 O you can Build a wired ventilation system from PPB 30 and PP 45 devices. The maximum number of fans used is 6. Various combinations are therefore possible, e.g. 2 x PP 45 K/O + 1 x PPB 30 K + 1 x RLS 45 K or 3 x PPB 30 K + 1 x RLS 45 K. A combination of PPB 30 K and RLS 45 O is not permitted. DS 45 RC: With the radio switch DS 45 RC you can build a radio-controlled ventilation system from PPB 30 RC and PP 45 RC devices, e.g. 4 x PP 45 RC + 1 x PPB 30 RC + 1 x DS 45 RC. PP 45 EO: If the RLS 45 K room air control is expanded with PP 45 EO, the wired devices can be combined with radio devices, e.g. 4x PP 45 K/O + 1 x PPB 30 RC + 1 x RLS 45 K + 1 x PP 45 EO. Optional accessories: Extension set PPB 30 VS, wall block PP 45 MB, compensating frame PPB 30 ARE and PPB 30 ARW, fastening plate PPB 30 ARE BB and PPB 30 ARW BB for compensating frame, humidity sensor PP 45 HYI and PP 45 HY, CO2 sensor PP 45 CO2 , VOC sensor PP 45 VOC, air filter, replacement PPB 30 G3, The room air controls RLS 45 K and RLS 45 O can be expanded with the internal humidity sensor PP 45 HYI or with the external sensors PP45 HY, PP 45 CO2 and PP 45 VOC. The devices achieve energy efficiency class A. The room air controls RLS 45 K and RLS 45 O can be operated in 5 ventilation levels 5/12/18/22/26 m3/h and 2 operating modes: continuous ventilation with heat recovery, cross ventilation without heat recovery and automatic operation. The RLS 45 K room air control also offers the option of conveniently configuring the device using the commissioning software on a PC/laptop (Windows). The settings can be saved as profiles and transferred to other controls. Functions: The recommended combination option is 2 x or 4 x PP 45 O/K + 1 x PPB 30 K + 1 x RLS 45 K. The recommended combination option for radio-controlled systems is 2 x or 4 x PP 45 RC + 1 or 2 x PPB 30 RC + 1 x DS 45 RC. In this case, the PPB 30 K/RC device can be operated in two different operating modes. In auto mode, the device works completely autonomously depending on the humidity value from the integrated sensor. In auto mode, the RLS 45 K room air control or the DS 45 RC radio switch only executes the external off and ventilation level 0 commands. In system operation, the device works completely according to the specifications of the room air control RLS 45 K or radio switch DS 45 RC. Only in the event of a moisture load (limit value adjustable) does the device disconnect from the system and start dehumidification. The automatic dehumidification system can be set as intensive ventilation mode (level 5 with heat recovery) or as exhaust air mode (45m3/h without heat recovery). In the event of an odor load, the intensive ventilation mode (level 5 with heat recovery) or exhaust air mode (45m3/h without heat recovery) can also be triggered manually with a button/switch. The duration of this function is adjustable (factory setting = 10 min). In the case of exhaust air operation from the PPB 30 K or PPB 30 RC, the PP 45 devices connected to the RLS 45 K room air control or programmed into the DS 45 RC radio switch provide the necessary supply air. The combination of PPB 30 K and exhaust air devices (e.g. ER/ECA) on an RLS 45 K room air control is not possible. A low-cost solution for the bathroom could be the combination of 1 x PPB 30 O + 1 x RLS 45 O. (Attention: The room air control has protection class IP 00). Exhaust air operation of 45 m3/h (without heat recovery and without volume flow compensation) can also be implemented. Heat exchanger: With the high-performance heat exchangers and the highly efficient EC fans, the devices achieve a heat supply level of 73% at the reference volume flow according to EN 13141-8. Installation instructions: Installation takes place in 2 steps: Installation of the shell sleeve PP 45 RHK (DN 160) or RHL (DN 160) and an outer cover in a core hole DN 160 with an inclination of 1-2%. We recommend drilling the core with DN 182 and aligning the inclination of the sleeve using the included Styrofoam wedges. The shell shell is protected from contamination with plaster protective covers. The final assembly set is then integrated. No pipe laying necessary and no adjustment of the system necessary. Electrical connection: The device is delivered assembled ready for use. Electrical connection is made using a plug connection. Connection to the RLS 45 K or RLS 45 O room air control via plug-in control cables. The 12 VDC power line from the room air control RLS 45 K / RLS 45 O to the device is also the control line. The PPB30 RC is connected directly to 230V. ATTENTION: Check the application area (protection zone) of the device. Condensate drain: The condensate is drained away via an integrated condensate drip edge in the outer cover. Item: PPB 30 K, delivery volume: 5 m3/h / 12 m3/h / 18 m3/h / 22 m3/h / 26 m3/h, energy efficiency class: A, rated voltage: 12 V DC, SPI value according to DIN EN 13141-8: 0.19 Wh/m3, maximum power consumption: 1.7 W / 2.5 W / 3.4 W / 4.4 W / 5, 3 W, protection class: IP G3/G3, connection diameter: 160 mm, width: 275 mm, height: 275 mm, depth: 410 mm, necessary wall opening: 162 to 182 mm, wall thickness: 320 mm / 500 mm, degree of heat provision at reference volume flow according to DIN EN 13141-8: 73.3%, necessary room air control: RLS 45 K, sound pressure level: 23 dB(A) / 35 dB(A) / 43 dB(A) / 48 dB(A) / 51 dB(A) / distance 1 m, free field conditions, Rated maximum element standard sound level difference Dn,w: 37 dB, type of ventilation: decentralized supply and exhaust air, heat recovery via: other, degree of heat provision: 73.3%